language:
Find link is a tool written by Edward Betts.searching for Macro instruction 16 found (22 total)
alternate case: macro instruction
Macro (computer science)
(3,850 words)
[view diff]
exact match in snippet
view article
In computer programming, a macro (short for "macro instruction"; from Greek μακρο- 'long, large') is a rule or pattern that specifies how a certain inputClipper architecture (1,263 words) [view diff] case mismatch in snippet view article find links to article
RISC processors. These instructions were implemented in a so-called Macro Instruction ROM within the Clipper CPU. This scheme allowed the Clipper to haveStart Input/Output (944 words) [view diff] exact match in snippet view article find links to article
IBM mainframe operating systems, Start Input/Output (STARTIO) is a macro instruction and a "branch entry" for low-level device access, where the programmerMicro-operation (835 words) [view diff] no match in snippet view article find links to article
registers. In a typical fetch-decode-execute cycle, each step of a macro-instruction is decomposed during its execution so the CPU determines and stepsMetafont (3,196 words) [view diff] exact match in snippet view article find links to article
"draw a lower case top of stem serif at point 4" might appear as one macro instruction (with the point as argument) in the program for a letter. For describingData Control Block (448 words) [view diff] exact match in snippet view article find links to article
in a program. A DCB is coded in Assembler programs using the DCB macro instruction (which expands into a large number of "define constant" instructions)Nord-100 (854 words) [view diff] no match in snippet view article find links to article
arithmetic, which in the ND-100 had been done in microcode. Along with the macro-instruction cache memory also in the ND-100, the ND-110 had a unique implementationBasic partitioned access method (561 words) [view diff] exact match in snippet view article find links to article
standard system macros OPEN, CLOSE, READ, WRITE,and CHECK. The NOTE macro instruction returns position of the last block read or written, and the POINTBasic sequential access method (418 words) [view diff] exact match in snippet view article find links to article
standard system macros OPEN, CLOSE, READ, WRITE,and CHECK. The NOTE macro instruction returns position of the last block read or written, and the POINTTRAC (programming language) (1,002 words) [view diff] case mismatch in snippet view article
Utah. Klaas van Schelven. "Don't say 'Homoiconic'". McIlroy, M.D., Macro Instruction Extensions of Compiler Languages. CACM 3, No. 4 (1960), 214–220. EastwoodDynamic linker (1,687 words) [view diff] exact match in snippet view article find links to article
programs in IBM OS/360 and its successors is done typically using a LINK macro instruction containing a Supervisor Call instruction that activates the operatingExtensible programming (1,731 words) [view diff] case mismatch in snippet view article find links to article
Fundamentals, Prentice-Hall, 1969, section III.7.2 McIlroy, M.D., "Macro Instruction Extensions of Compiler Languages", Communications of the ACM 3 noIEFBR14 (1,196 words) [view diff] no match in snippet view article find links to article
Initiator initially "attaches" the job-step task using the ATTACH macro-instruction (SVC 42), and "unwinding" the effect of this ATTACH macro (it beingHistory of operating systems (4,484 words) [view diff] case mismatch in snippet view article find links to article
was contemporaneous with the Ferranti Atlas 705 Autocoder System Macro Instruction Manual (PDF) (second ed.), February 1957, 22-6726-1 The USE CompilerTTM (programming language) (1,378 words) [view diff] case mismatch in snippet view article
Technology, Willis H. Booth Computing Center (1964). McIlroy, M.D., Macro Instruction Extensions of Compiler Languages. CACM 3, No. 4 (1960), 214-220. CaineException handling syntax (4,752 words) [view diff] exact match in snippet view article find links to article
Exception_Message(Error)); end Foo; Most assembly languages will have a macro instruction or an interrupt address available for the particular system to intercept